收藏本站
AT26DF161
some point before the erase cycle completes, the WEL bit in the Status Register will be reset
back to the logical “0” state.
The device also incorporates an intelligent erasing algorithm that can detect when a byte loca-
tion fails to erase properly. If an erase error occurs, it will be indicated by the EPE bit in the
Status Register.
Figure 8-4.
Chip Erase
CS
0
1
2
3
4
5
6
7
SCK
OPCODE
SI
C
C
C
C
C
C
C
C
MSB
SO
9. Protection Commands and Features
HIGH-IMPEDANCE
9.1
Write Enable
The Write Enable command is used to set the Write Enable Latch (WEL) bit in the Status Regis-
ter to a logical “1” state. The WEL bit must be set before a program, erase, Protect Sector,
Unprotect Sector, or Write Status Register command can be executed. This makes the issuance
of these commands a two step process, thereby reducing the chances of a command being
accidentally or erroneously executed. If the WEL bit in the Status Register is not set prior to the
issuance of one of these commands, then the command will not be executed.
To issue the Write Enable command, the CS pin must first be asserted and the opcode of 06h
must be clocked into the device. No address bytes need to be clocked into the device, and any
data clocked in after the opcode will be ignored. When the CS pin is deasserted, the WEL bit in
the Status Register will be set to a logical “1”. The complete opcode must be clocked into the
device before the CS pin is deasserted; otherwise, the device will abort the operation and the
state of the WEL bit will not change.
Figure 9-1.
Write Enable
CS
0
1
2
3
4
5
6
7
SCK
OPCODE
SI
0
0
0
0
0
1
1
0
MSB
SO
HIGH-IMPEDANCE
11
3599H–DFLASH–8/09
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AT26DF161A-MU IC FLASH 16MBIT 70MHZ 8QFN
AT26DF321-SU IC FLASH 32MBIT 66MHZ 8SOIC
AT27BV010-90JU IC OTP 1MBIT 90NS 32PLCC
AT27BV020-90JU IC OTP 2MBIT 90NS 32PLCC
AT27BV040-12JU IC OTP 4MBIT 120NS 32PLCC
AT27BV1024-90JU IC OTP 1MBIT 90NS 44PLCC
AT27BV256-70JU IC OTP 256KBIT 70NS 32PLCC
AT27BV4096-12VI IC OTP 4MBIT 120NS 40VSOP
相关代理商/技术参数
AT26DF321 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-megabit 2.7-volt Only Serial Firmware DataFlash Memory
AT26DF321_06 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-megabit 2.7-volt Only Serial Firmware DataFlash Memory
AT26DF321_07 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-megabit 2.7-volt Only Serial Firmware DataFlash Memory
AT26DF321-S3U 功能描述:闪存 32M SERIAL FLASH - IND TEMP RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
AT26DF321-SU 功能描述:闪存 32M SERIAL FLASH - IND TEMP RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
AT26DF321-SU SL514 制造商:Atmel Corporation 功能描述:
AT26F004 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:4-megabit 2.7-volt Only Serial Firmware DataFlash Memory
AT26F004_06 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:4-megabit 2.7-volt Only Serial Firmware DataFlash Memory